Tools
-
Stock Code:SWTL-DSD
Fox/Marzocchi Basic Damper Shaft Driver. A simple, affordable driver that threads onto the rebound shaft to safely knock the lowers off without damaging rebound or VVC internals.
What It Does:
- Threads onto the rebound shaft (damper side)
- Protects the meter rod, rebound assembly & VVC internals
- Lets you tap out the lowers without metal-on-metal impact
- Soft replaceable plastic tip (cheap + safe)
- Equivalent to Fox 398-00-682
Compatibility:
- Fox 34 / 36 / 38 / 40 – all years (damper side only)
- Marzocchi Bomber forks using Fox internals
- Not compatible with Taper-Cast forks$39.50 (RRP)Add To Cart
-
Stock Code:SWTL-DLDSD
Deluxe Fox/Marzocchi Fork Shaft Driver – Damper + Air Side
The upgraded dual-side driver for safely knocking out both damper and air shafts during lower-leg service. One tool replaces two separate Fox drivers.
What It Does:
- One end fits Fox/Marzocchi air shafts
- Other end uses a replaceable threaded tip for damper shafts
- Protects VVC rods / meter rods from impact damage
- Built for rubber mallet or wood block impact (no metal-on-metal)
- Same soft tips as our Basic Driver
Premium feel: larger, more stable body with dual-ended support.$62.50 (RRP)Add To Cart
-
Stock Code:SWTL-QDFD
The Quick Drop Fork Dummy lets you remove a fork from a bike in seconds without losing any headset or cockpit hardware. Bearings stay seated, spacers stay in order, and the stem remains aligned while the fork is out. Built for fast bikeshop jobs.
HOW IT WORKS
The tip of the Top Part matches the inner diameter of a standard steerer tube. It is slightly tapered and features a strong integrated neodymium magnet.
Remove your top cap, insert the Quick Drop into the steerer from above, and push the fork downward. As the fork slides down, the tool stays into the steer tube being held by the tight tolerances and the magnet.
You can guide the fork down or lightly pull it while the tool follows smoothly into the headset and frame, holding bearings, spacers, and stem in position.
The lower bearing may stay on the fork during removal. If using the Top + Bottom Kit, place that bearing onto the bottom piece, reinsert both parts into the frame, align them, then rotate 180° to lock the system together.
The magnetic tip also makes reinstallation easier. When guiding the steerer back into position, the magnet helps catch and align the tool instantly, making engagement quick and controlled.
The holding force is strong enough to keep everything composed, even allowing the bike to be turned upside down temporarily if needed during service or short-term storage.$44.90 (RRP)Add To Cart
-
Stock Code:SWTL-QDL
The QuickDrop Lite is built for maximum workshop efficiency. It keeps your headset stack perfectly organized during fork removal and makes reinstallation even faster thanks to its integrated top handle. Simple, fast, and made for mechanics who do this all day.
HOW IT WORKS
The lower section of the Quick Drop Lite matches the inner diameter of a standard steerer tube with tight, workshop-ready tolerances.
Remove your top cap, insert the tool from above, and guide the fork downward. The Lite stays engaged inside the steerer, holding spacers, stem, and headset bearings aligned while the fork slides out.
The large integrated handle gives you direct control during both removal and reinstallation. You can guide the fork smoothly with one hand while keeping everything centered and stable.
During reinstall, simply guide the steerer back up while lightly holding the handle. The alignment stays straight, spacers remain stacked, and components slide back into place without juggling.$22.50 (RRP)Add To Cart
-
Stock Code:SWTL-SFC
The Sealant Funnel Core is the all-in-one tool for fast, clean tubeless setup. It combines a full-size sealant funnel and a valve-core remover at the tip, letting you pull the core, add sealant, and reinstall it, all without switching tools.
How It Works
Unscrew your valve core using the integrated remover at the tip. Then screw the funnel onto your Presta valve and pour sealant directly into the tires. Once filled, just reinstall your valve core with the same tool.
The funnel threads make a tight, leak-free seal. As soon as the tool stops turning, you’re fully sealed and nothing drips through the valve.$28.00 (RRP)Add To Cart
-
Stock Code:SWTL-SS120
SteerStation Fork Steer Tube Offset Clamp
The best solution for fork work. SteerStation mounts directly to mountain bike steer tube and offsets the fork away from the vise, giving you complete positioning freedom with zero risk of crown or lowers contacting the vise body.
Important Compatibility Info
- Designed for 1-1/8" bike steerer tubes.
- For bench vise use only.
Offset Options
- Standard Offset (70 mm) – Ideal for most service work. Clears the vise while keeping compact leverage.
- Extended Offset (120 mm) – Maximum clearance and working freedom. More reach, more access, slightly higher cost.
Both versions dramatically improve fork positioning compared to direct steerer clamping.$74.90 (RRP)Add To Cart
-
Stock Code:SWTL-SS70
SteerStation Fork Steer Tube Offset Clamp
The best solution for fork work. SteerStation mounts directly to mountain bike steer tube and offsets the fork away from the vise, giving you complete positioning freedom with zero risk of crown or lowers contacting the vise body.
Important Compatibility Info
- Designed for 1-1/8" bike steerer tubes.
- For bench vise use only.
Offset Options
- Standard Offset (70 mm) – Ideal for most service work. Clears the vise while keeping compact leverage.
- Extended Offset (120 mm) – Maximum clearance and working freedom. More reach, more access, slightly higher cost.
Both versions dramatically improve fork positioning compared to direct steerer clamping.$56.90 (RRP)Add To Cart
-
Stock Code:SWTL-SACW
2-in-1 FOX-(Rockshox 2024+) Suspension Wrench
This 3D-printed multi-tool combines the 2 most common FOX fork tools into one compact, trail-ready wrench. Perfect for both workshop use and quick adjustments on the trail.$10.85 (RRP)Add To Cart
-
Stock Code:SWTL-UDPH
Universal Dropper Post Holder | Hands-Free Install & Service
Installing or servicing a dropper post means working on the lever end at the bar while trying not to kink a cable or hose at the post. The Universal Dropper Post Holder locks the post in place so you can see what’s happening at both ends, no third hand required.
What Makes It Different
- All-size compatibility: Works with 27.2, 30.9, 31.6, and 34.9 mm posts. Adapters included; 30.9/31.6 share the same insert for fast swaps.
- TPU strap system: Wide, grippy strap conforms to any post diameter.
- Bleed-through access: Rear service port lets you bleed hydraulic posts (e.g., RockShox) without removing the holder.
- Cable/hose friendly: Elevates and stabilizes the post so housing won’t kink while you work the lever at the bar.
- Bench-ready design: Compact footprint with replaceable adapters, built for daily use in busy workshops.
How to Use
1. Choose the adapter for your post size and drop it into the base.
2. Set the post in the cradle, align the cable/hose path, and secure with the TPU strap.
3. Route and tension the cable (or connect the hose) while operating the lever at the handlebar.
4. For hydraulic posts, position the bleed port over the rear service hole and perform the bleed.
5. When you're done, unstrap it and pull out the tool.$68.00 (RRP)Add To Cart
-
Stock Code:SWTL-SDTPRO
Universal Rear Shock Dummy Tool – PRO Version
The PRO version is the heavy-duty, workshop-grade upgrade to our standard Rear Shock Dummy Tool. Built for mechanics and advanced users who frequently switch between eyelet and trunnion mounting, it’s stronger, stiffer, and optimized for repeated use.
Adjustment Range:
165 mm to 250 mm (and up to ~266 mm for legacy sizes). One full rotation = 10 mm of length change. Set your eye-to-eye and lock it in seconds.
What Makes It PRO
- Full top-section swap: Unscrews completely for instant conversion between eyelet and trunnion. Each adapter self-aligns perfectly perpendicular.
- High-strength polymer body: Thicker, stiffer, and designed to withstand repeated workshop use without flexing.
- Maintenance-friendly interface: If the top gets snug, insert a screwdriver in the slot to unscrew. No need to overtighten.
- Heavy-duty load capacity: Over 20 kg of static load (not for riding or sitting).
- Thread-and-align system: Rotate until the Triangle marks your length. Going 10 mm under is still good practice for eyelet clearance.$77.90 (RRP)Add To Cart
-
Stock Code:SWTL-USTD
Pulling your fork should not turn your bike into a pile of headset parts. The Universal Steerer Tube Dummy replaces your fork’s steerer so your headset stack stays exactly where it belongs: bearings seated, spacers aligned, stem in place. No loose hardware, no “where did that spacer go”, no caliper hanging by the hose.
Compatibility
- Universal fit: Designed for standard 1-1/8" (28.6 mm) steerers, works with both straight and tapered forks.
- Not compatible: oversized “Overdrive” steerers found on some older Giant bikes.
- Standard length: 220 mm (covers the huge majority of bikes).$56.90 (RRP)Add To Cart
-
Stock Code:SMTL82006
Ten functions including 8mm hex for cranks and a Torx 25 for disc rotor bolts
- Hex: 2, 2.5, 3, 4, 5, 6mm
- #2 Philips head screwdriver
- #5 Flat head screwdriver
- 8mm hex(fits over the 6mm)
- Torx 25 wrench.$38.00 (RRP)Add To Cart
-
Stock Code:SLTL-TL0069
Surly Fat Bike Wheelbuilding Tools
· 35mm-wide spacer aids in dishing and truing Pugsley offset wheelsPOA -
Stock Code:WMTL-GXP22-EXTStock Code:WMTL-BE-22MM-SETStock Code:WMTL-BE-24MM-SETStock Code:WMTL-24X37-EXTStock Code:WMTL-BE-25MM-SETStock Code:WMTL-29MM-EXTStock Code:WMTL-BE-29MM-SETStock Code:WMTL-BE-30MM-SETStock Code:WMTL-608-EXTStock Code:WMTL-609-EXTStock Code:WMTL-6000-EXTStock Code:WMTL-6001-EXTStock Code:WMTL-6002-EXTStock Code:WMTL-6003-EXTStock Code:WMTL-6804-EXTStock Code:WMTL-6805-EXTStock Code:WMTL-6806-EXTStock Code:WMTL-EX0001Stock Code:WMTL-EX0002Stock Code:WMTL-EX0003Stock Code:WMTL-BE-PUSHERStock Code:WMTL-PUSHERStock Code:WMTL-R6-EXT
6000, 6200, 6800 & 6900 (10mm) Sealed Bearing Extractor
Individual extractor for removing 6000, 6200, 6800 & 6900 sealed bearings
6000: Bearing ID: 10mm / OD: 26mm / Width: 8mm
6200: Bearing ID: 10mm / OD: 30mm / Width: 9mm
6800: Bearing ID: 10mm / OD: 19mm / Width: 5mm
6900: Bearing ID: 10mm / OD: 22mm / Width: 6mm
Insert the extractor into the bearing, tighten one side with an Allen key, and the collet expands to grip the inside of the bearing
Tap the extractor out with a punchExpected Date:07 May 2026Expected Date:07 May 2026$49.00 (RRP)$65.00 (RRP)$65.00 (RRP)$75.00 (RRP)$65.00 (RRP)$80.00 (RRP)$65.00 (RRP)$65.00 (RRP)$72.00 (RRP)$72.00 (RRP)$72.00 (RRP)$72.00 (RRP)$72.00 (RRP)$72.00 (RRP)$74.00 (RRP)$74.00 (RRP)$74.00 (RRP)$239.00 (RRP)$226.00 (RRP)$239.00 (RRP)$26.00 (RRP)$19.00 (RRP)$75.00 (RRP) -
Stock Code:WMTL-1526OBStock Code:WMTL-1728OBStock Code:WMTL-2437OBStock Code:WMTL-27537OBStock Code:WMTL-6000OBStock Code:WMTL-6001OBStock Code:WMTL-6002OBStock Code:WMTL-6003OBStock Code:WMTL-6801OB-1Stock Code:WMTL-6802OB-1Stock Code:WMTL-6803OB-1Stock Code:WMTL-6804OBStock Code:WMTL-6805OBStock Code:WMTL-6806OBStock Code:WMTL-6900OB-1Stock Code:WMTL-6901OB-1Stock Code:WMTL-6901OB-2Stock Code:WMTL-6902OBStock Code:WMTL-6903OBStock Code:WMTL-6904OBStock Code:WMTL-GXP-LEFT
Open Bore adapters, also known as drifts, are used to press cartridge bearings in to bottom bracket cups, hub shells, freehub bodies and suspension frame pivots. Each adapter has a smaller diameter that inserts in to the center of a bearing, and a larger diameter section that matches the outside diameter of the bearing. When used with a bearing press, the adapter presses against the races of the bearing, properly aligns the bearing and prevents damage as the bearing is pressed in.
Our 1526 open bore adapter is used to press 26x15 sealed bearings. The adapter is machined with one step at 15mm OD, which fits in to the center of the sealed bearing.
Installs: 15267, 15268 bearings
Inner Step Outer Diameter: 14.8mm
Outer Diameter: 25.8mm
Thru Hole Diameter: 0.387" (9.8mm)
Inner hole sized to fit 3/8" ACME threaded rod
Compatible with PRESS-1 or PRESS-4 handles
Machined, red anodized aluminum
Sold individually (2 drifts required for some installations)Expected Date:07 May 2026Expected Date:07 May 2026$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$21.00 (RRP) -
Stock Code:WMTL-29SRAM-OB
29mm open bore adapter is used to press 29mm x 42mm (DUB) sealed bearings. The adapter is machined with one step at 29mm OD, which fits into the center of the sealed bearing. For use with Wheels Mfg Bottom Bracket Press (PRESS-7, PRESS-7-PRO or PRESS-9-PRO)
Installs: 29X42 (DUB) bearing
Inner Step Outer Diameter: 41.8mm
Outer Diameter: 28.9mm
Thru Hole Diameter: 12.8mm (1/2")
Thickness: 7mm
Compatible with PRESS-7, PRESS-7-PRO or PRESS-9-PRO handles/rod.
Machined, red anodized aluminum
Sold individuallyExpected Date:07 May 2026$18.00 (RRP) -
Stock Code:WMTL-6000OA-6Stock Code:WMTL-6001OA-7Stock Code:WMTL-6002OA-7Stock Code:WMTL-6003OA-7Stock Code:WMTL-6802OA-20Stock Code:WMTL-6803OA-20Stock Code:WMTL-6804OA-20Stock Code:WMTL-6900OA-40Stock Code:WMTL-6901OA-2Stock Code:WMTL-6901OA-40Stock Code:WMTL-6902OA-7Stock Code:WMTL-6903OA-7Stock Code:WMTL-6904OA-7
Our 6000 over axle adapter is used to press 6000 sealed bearings into hub shells or suspension components. An over axle adapter is necessary when the bearing slides over the axle before it is pressed into the hub shell or suspension component. In addition to the adapter, you often need spacers to clear the end of the axle and allow enough clearance for the press to fully push in the bearing.
Installs: 6000 bearing
Outer Diameter: 25.8mm
Thickness: 6mm
Thru Hole Diameter: 10.2mm
Compatible with PRESS-1 or PRESS-4 handles
Machined, red anodized aluminum
Sold individually (multiple adapters required for some installations)Expected Date:07 May 2026Expected Date:07 May 2026Expected Date:07 May 2026$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$20.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP) -
Stock Code:WMTL-6900OB
Our 6900 open bore adapter is used to press 6900 sealed bearings. The adapter is machined with one step at 9.9mm OD, which fits into the center of the sealed bearing.
- Installs: 6900 bearing
- Inner Step Outer Diameter: 9.9mm
- Outer Diameter: 21.8mm
- Thickness: 5.9mm
- Thru Hole Diameter: 5.2mm
- Inner hole sized to fit quick release skewer or M5 bolt
- Compatible with PRESS-2
- Machined, red anodized aluminum
- Sold individually (2 drifts required for some installations)$18.00 (RRP) -
Stock Code:WMTL-BP0009
A new and more efficient take on the classic Wheels MFG threaded press handles. The Adjustable Press Stop makes life easier for bike mechanics as it allows for quick and accurate positioning at the press of a button. The Adustable Press Stop slides along 1/2" UNC threaded press rod when the button is depressed and can be placed quickly to secure drifts, spacers, and cups when completing maintenance or installation of bike headsets, bottom brackets, and bearings.
Product Details:
Compatible with new and existing Wheels MFG press kits which are sold separately including:
Press-7
Press-7-Pro
Press-8
Press-9-Pro$119.00 (RRP)Add To Cart
-
Stock Code:WMTL-BP0022
Similar to its big brother but at a fraction of the size. The new and more efficient Adjustable Press Stop Mini will make life easier for mechanics as it allows for quick and accurate positioning in places where space is tight at the press of a button.
The Adustable Press Stop slides along 3/8" ACME threaded press rod when the button is depressed and can be placed quickly to secure drifts, spacers, and cups when completing maintenance or installation of bike headsets, bottom brackets, and bearings.
Product Details:
Compatible with new and existing Wheels MFG press kits which are sold separately including:
Press-4
ST0006
Press-1
Machined aluminum body
Anodized in Wheels MFG red.
Durable steel button
For use with 3/8" ACME threaded press rod (Sold Separately)$113.00 (RRP)Add To Cart
-
Stock Code:WMTL-AXLERULER-PRO
Feast your eyes on the Axle Ruler Pro – the precision tool that's about to revolutionize your bike mechanic game! Crafted with pure stoke by the legends at Wheels Manufacturing, this bad boy is here to make sure you never second-guess those axle measurements again.
Need to find your Axle thread pitch? We have you covered with a wide range of measurements in both male and female for Solid, QR and Thru Axles including:
M9x1, M9x26, 3/8"x24, 3/8"x26, M10x1, M10x26, M12x1, M12x1.25, M12x1.5, M12x1.75, M14x1.5, M15x1, M15x1.5
No more noodling around with different sizes – the Axle Ruler Pro has it all, so you can lock in those measurements with style.
The self-centering axle measurement channel is a game-changer, making axle length measurements a breeze. With an 11-inch and a 28-centimeter ruler in the mix, the Axle Ruler Pro adapts to your vibe. Inches or centimeters, take your pick – it's all about giving you the freedom to roll your way.
Axle length, thread size, pitch or length – whatever you need, this ruler's got your back. No more overthinking, just pure accuracy.
Crafted from 6061 aluminum.$212.00 (RRP)Add To Cart
-
Stock Code:WMTL-TL9002
E-bike Hub Drive Cassette Socket Bafang
E-bikes are here to stay! Designed to save the mechanic time and money, our new e-bike sockets are machined to match manufacturer specifications.
The E-bike Hub Drive Cassette Socket is used installing and removing compatible cassettes on Bafang hub-drive motors without removing motor wiring.
- 8620 Steel
- Zinc finishExpected Date:07 May 2026$64.00 (RRP) -
Stock Code:WMTL-EX0004
Bearing extractors set for pushing out 22mm, 24mm, 29, and 30mm ID sealed bearings from bottom bracket cups. Compatible with our 1/2" threaded press rod and handles (PRESS-7 and PRESS-7-PRO).
Includes
(1) 30mm ID sealed bearing extractor
(1) 29mm ID sealed bearing extractor
(1) 24mm ID sealed bearing extractor
(1) 22mm ID sealed bearing extractor
(1) 52mm receiver cup
(1) 44mm receiver cup sleeve
(1) 42mm receiver cup sleeve
(1) 39mm receiver cup sleeve
(1) bearing pusher shaft
Extractors for 25mm and 29mm ID bearings available separately:
BE-25MM-SET$276.00 (RRP)Add To Cart
