Shockwave SteerStation 70mm
Description
SteerStation Fork Steer Tube Offset Clamp
The best solution for fork work. SteerStation mounts directly to mountain bike steer tube and offsets the fork away from the vise, giving you complete positioning freedom with zero risk of crown or lowers contacting the vise body.
Important Compatibility Info
- Designed for 1-1/8" bike steerer tubes.
- For bench vise use only.
Offset Options
- Standard Offset (70 mm) – Ideal for most service work. Clears the vise while keeping compact leverage.
- Extended Offset (120 mm) – Maximum clearance and working freedom. More reach, more access, slightly higher cost.
Both versions dramatically improve fork positioning compared to direct steerer clamping.
Webshops and Bike shops
You may also be interested in...
-
Stock Code:WMTL-6000OA-6Stock Code:WMTL-6001OA-7Stock Code:WMTL-6002OA-7Stock Code:WMTL-6003OA-7Stock Code:WMTL-6802OA-20Stock Code:WMTL-6803OA-20Stock Code:WMTL-6804OA-20Stock Code:WMTL-6900OA-40Stock Code:WMTL-6901OA-2Stock Code:WMTL-6901OA-40Stock Code:WMTL-6902OA-7Stock Code:WMTL-6903OA-7Stock Code:WMTL-6904OA-7
Our 6000 over axle adapter is used to press 6000 sealed bearings into hub shells or suspension components. An over axle adapter is necessary when the bearing slides over the axle before it is pressed into the hub shell or suspension component. In addition to the adapter, you often need spacers to clear the end of the axle and allow enough clearance for the press to fully push in the bearing.
Installs: 6000 bearing
Outer Diameter: 25.8mm
Thickness: 6mm
Thru Hole Diameter: 10.2mm
Compatible with PRESS-1 or PRESS-4 handles
Machined, red anodized aluminum
Sold individually (multiple adapters required for some installations)Expected Date:15 September 2026$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$20.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP) -
Stock Code:BBTL-MTB32TOStock Code:BBTL-MTB34TOStock Code:BBTL-MTB35/36TOStock Code:BBTL-MTB38TOStock Code:BBTL-MTB40TO$64.93 (RRP)$64.93 (RRP)$64.93 (RRP)$64.93 (RRP)$64.93 (RRP)
-
Stock Code:ABTLABT-SHCRANK
The Shimano Crank Tool (SCT for short) is specifically built to service the chainring lockring on Shimano single ring cranksets for 12 speed drivetrains. It features a large hex that can be used with a 1.5" or 38mm wrench or locked into a vise.
The clearance hole is kept to a minimum to keep the tool engaged on the low profile lockring, minimizing the chance of damaging the tool or parts.
Compatibility:
Chain ring lockrings on Shimano 12spd mountain crank sets.
XT and Ultegra bottom brackets
Made in Bend Oregon$76.00 (RRP)Add To Cart
-
Stock Code:RLTL-NMAKIT
A 3 Pack of 10/13/14 Gauge fully plastic applicators.
Produces bead of material when dispensed, size dependent on gauge.
Full plastic construction prevents scratching of delicate surfaces.
For use on bearings, freehub bodies, shifters, and lubricating small mechanisms.
Luer-Lock Compatible
Crushproof Polypropylene Connector
14 gauge Opening for Precise Control
Guaranteed For Life!$12.00 (RRP) -
Stock Code:ABTL-SLPRS-DRVR32MM
This tool make dust wiper installation an easy sure fired task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm.
The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet.
The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time.
Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.
Made in Bend Oregon.$56.00 (RRP)Add To Cart
