Abbey Fork Seal Press Driver - 36mm
Description
This tool make dust wiper installation an easy sure fired task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm.
The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet.
The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time.
Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.
Made in Bend Oregon.
Webshops and Bike shops
You may also be interested in...
-
Stock Code:WMTL-GXP22-EXTStock Code:WMTL-BE-22MM-SETStock Code:WMTL-BE-24MM-SETStock Code:WMTL-24X37-EXTStock Code:WMTL-BE-25MM-SETStock Code:WMTL-29MM-EXTStock Code:WMTL-BE-29MM-SETStock Code:WMTL-BE-30MM-SETStock Code:WMTL-608-EXTStock Code:WMTL-609-EXTStock Code:WMTL-6000-EXTStock Code:WMTL-6001-EXTStock Code:WMTL-6002-EXTStock Code:WMTL-6003-EXTStock Code:WMTL-6804-EXTStock Code:WMTL-6805-EXTStock Code:WMTL-6806-EXTStock Code:WMTL-EX0001Stock Code:WMTL-EX0002Stock Code:WMTL-EX0003Stock Code:WMTL-BE-PUSHERStock Code:WMTL-PUSHERStock Code:WMTL-R6-EXT
6000, 6200, 6800 & 6900 (10mm) Sealed Bearing Extractor
Individual extractor for removing 6000, 6200, 6800 & 6900 sealed bearings
6000: Bearing ID: 10mm / OD: 26mm / Width: 8mm
6200: Bearing ID: 10mm / OD: 30mm / Width: 9mm
6800: Bearing ID: 10mm / OD: 19mm / Width: 5mm
6900: Bearing ID: 10mm / OD: 22mm / Width: 6mm
Insert the extractor into the bearing, tighten one side with an Allen key, and the collet expands to grip the inside of the bearing
Tap the extractor out with a punch$49.00 (RRP)$65.00 (RRP)$65.00 (RRP)$75.00 (RRP)$65.00 (RRP)$80.00 (RRP)$65.00 (RRP)$65.00 (RRP)$72.00 (RRP)$72.00 (RRP)$72.00 (RRP)$72.00 (RRP)$72.00 (RRP)$72.00 (RRP)$74.00 (RRP)$74.00 (RRP)$74.00 (RRP)$239.00 (RRP)$226.00 (RRP)$239.00 (RRP)$26.00 (RRP)$19.00 (RRP)$75.00 (RRP) -
Stock Code:PDTL6460631
Pedro's Fixed Torque Drivers are shop quality preset torque wrenches designed with an infinite torque-limiting clutch design to eliminate over-torquing of critical parts. Each wrench is calibrated using a torque calibration analyzer accurate to +/- 1 percent and is then tested 5 times prior to packaging with results recorded on the product card along with the date.
Infinite torque-limiting clutch design eliminates over-torquing.
Magnetic socket drive accepts standard 1/4" hex bits. 4mm, 5mm, & T25 bits included.
Ergonomic handle design provides comfort and control and stores extra bits.$75.00 (RRP)Add To Cart
-
Stock Code:EVTL-EVTGP
Protect Your Investment! EVT tools are built to last a lifetime — but one drop is all it takes to destroy a delicate gauge. That’s why The Gauge Protector is a must-have. Made from durable, ribbed rubber, it cushions your gauge against impact and helps prevent costly damage from falls or knocks.
$25.00 (RRP)Add To Cart
-
Stock Code:EVTL-EVTPRESTA
The Presta-Only Inflator is built with characteristic EVT durability and ease-of-use.
It features a bead-popping high-flow presta chuck and a high-quality American-made lever mechanism.
This inflator features our custom super-low-durometer urethane pump washer, which provides a great seal and lasts much longer than rubber.$210.00 (RRP) -
Stock Code:SWTL-USTD
Pulling your fork should not turn your bike into a pile of headset parts. The Universal Steerer Tube Dummy replaces your fork’s steerer so your headset stack stays exactly where it belongs: bearings seated, spacers aligned, stem in place. No loose hardware, no “where did that spacer go”, no caliper hanging by the hose.
Compatibility
- Universal fit: Designed for standard 1-1/8" (28.6 mm) steerers, works with both straight and tapered forks.
- Not compatible: oversized “Overdrive” steerers found on some older Giant bikes.
- Standard length: 220 mm (covers the huge majority of bikes).$56.90 (RRP)Add To Cart
