Abbey Hanger Alignment Gauge ( HAG)
Description
The HAG is the last hanger tool you'll ever have to buy.
WHY YOU NEED ONE
The derailleur hanger is the foundation for the modern drive train to work properly. With modern bikes getting as many as 13 cogs in the space that we use to put 8 it's never been more important to make sure the hanger is perfectly straight. Sadly many of the current tools just aren't capable of achieving this kind of precision.
WHAT MAKES THE HAG THE BEST
We went through extra steps to make this tool half precision measuring instrument and half pry bar.
- Tolerances as tight as a quarter of a thousandth of an inch (.0063mm) in some critical dimensions of this tool.
- Ability to lock in the feeler so you don't have to second guess your measurement after bumping it on the tire. T
- Top half of tool will rotate out of the way of fender stays and frame tubes.
- Feeler gauge stick stores inside the top half of the tool, very handy for the traveling mechanic.
- T bolt extends past the tool for access to those problematic hangers found on some modern full suspension bikes.
- Re-buildable. While ideally your HAG should be sent back for a rebuild, it is possible to do them in the field by replacing the brass bushing in the T-Bolt.
Made in Bend Oregon.
Webshops and Bike shops
You may also be interested in...
-
Stock Code:WMTL-6000OA-6Stock Code:WMTL-6001OA-7Stock Code:WMTL-6002OA-7Stock Code:WMTL-6003OA-7Stock Code:WMTL-6802OA-20Stock Code:WMTL-6803OA-20Stock Code:WMTL-6804OA-20Stock Code:WMTL-6900OA-40Stock Code:WMTL-6901OA-2Stock Code:WMTL-6901OA-40Stock Code:WMTL-6902OA-7Stock Code:WMTL-6903OA-7Stock Code:WMTL-6904OA-7
Our 6000 over axle adapter is used to press 6000 sealed bearings into hub shells or suspension components. An over axle adapter is necessary when the bearing slides over the axle before it is pressed into the hub shell or suspension component. In addition to the adapter, you often need spacers to clear the end of the axle and allow enough clearance for the press to fully push in the bearing.
Installs: 6000 bearing
Outer Diameter: 25.8mm
Thickness: 6mm
Thru Hole Diameter: 10.2mm
Compatible with PRESS-1 or PRESS-4 handles
Machined, red anodized aluminum
Sold individually (multiple adapters required for some installations)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$20.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP) -
Stock Code:PDTL6462117
Precision laser cut design with ergonomic cushioned TPR grip and 3/8" drive for use with torque wrenches.
Superior material and optimized heat treatment outlast the competition.$33.00 (RRP)Add To Cart
-
Stock Code:ABTLABTSPD34MM
This tool make dust wiper installation an easy sure fired task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm.
The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet.
The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time.
Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.
Made in Bend Oregon.$56.00 (RRP)Add To Cart
-
Stock Code:SWTL-DSD
Fox/Marzocchi Basic Damper Shaft Driver. A simple, affordable driver that threads onto the rebound shaft to safely knock the lowers off without damaging rebound or VVC internals.
What It Does:
- Threads onto the rebound shaft (damper side)
- Protects the meter rod, rebound assembly & VVC internals
- Lets you tap out the lowers without metal-on-metal impact
- Soft replaceable plastic tip (cheap + safe)
- Equivalent to Fox 398-00-682
Compatibility:
- Fox 34 / 36 / 38 / 40 – all years (damper side only)
- Marzocchi Bomber forks using Fox internals
- Not compatible with Taper-Cast forks$39.50 (RRP)Add To Cart
-
Stock Code:PDTL6400100
Tyre Levers 24 Pair Counter Display
- Award winning and universally loved.
- Molded box construction and proprietary plastic blend makes these the strongest levers available.
- Chisel tip shape is easy to insert beneath the bead and the slightly thicker shape keeps the tire lever from slipping.
- Bold shape makes it easy to remove the tightest of tyres without bending or breaking.
Backed by Pedro's lifetime warranty, and we will happily replace them for you.POA
