Abbey Fork Seal Press Driver - 40mm
Description
This tool make dust wiper installation an easy sure fired task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm.
The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet.
The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time.
Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.
Made in Bend Oregon.
Webshops and Bike shops
You may also be interested in...
-
Stock Code:WMTL-6000OA-6Stock Code:WMTL-6001OA-7Stock Code:WMTL-6002OA-7Stock Code:WMTL-6003OA-7Stock Code:WMTL-6802OA-20Stock Code:WMTL-6803OA-20Stock Code:WMTL-6804OA-20Stock Code:WMTL-6900OA-40Stock Code:WMTL-6901OA-2Stock Code:WMTL-6901OA-40Stock Code:WMTL-6902OA-7Stock Code:WMTL-6903OA-7Stock Code:WMTL-6904OA-7
Our 6000 over axle adapter is used to press 6000 sealed bearings into hub shells or suspension components. An over axle adapter is necessary when the bearing slides over the axle before it is pressed into the hub shell or suspension component. In addition to the adapter, you often need spacers to clear the end of the axle and allow enough clearance for the press to fully push in the bearing.
Installs: 6000 bearing
Outer Diameter: 25.8mm
Thickness: 6mm
Thru Hole Diameter: 10.2mm
Compatible with PRESS-1 or PRESS-4 handles
Machined, red anodized aluminum
Sold individually (multiple adapters required for some installations)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$20.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP)$18.00 (RRP) -
Stock Code:PDTL6462114
Precision laser cut design with ergonomic cushioned TPR grip and 3/8" drive for use with torque wrenches.
Superior material and optimized heat treatment outlast the competition.$33.00 (RRP)Add To Cart
-
Stock Code:EVTL-EVTKS6
The Knuckle Saver Pedal Wrench Adaptor helps removing stubborn hex-mounted pedal spindles, and is available in 6 and 8 mm versions.
Combine this tool with a pedal wrench to easily and safely remove or install. Position your hands for maximum leverage while ensuring they don't impact anything but air when it breaks loose. The knurled surface helps you spin it on and off.
Knuckle Savers work with any pedal wrench. This tool is also helpful with tight 8mm crank anchor bolts, especially self-extracting ones. Ergonomics are incalculably better than a naked hex wrench. Your tendons, joints and knuckles will thank you!$62.00 (RRP)Add To Cart
-
Stock Code:SWTL-QDFD
The Quick Drop Fork Dummy lets you remove a fork from a bike in seconds without losing any headset or cockpit hardware. Bearings stay seated, spacers stay in order, and the stem remains aligned while the fork is out. Built for fast bikeshop jobs.
HOW IT WORKS
The tip of the Top Part matches the inner diameter of a standard steerer tube. It is slightly tapered and features a strong integrated neodymium magnet.
Remove your top cap, insert the Quick Drop into the steerer from above, and push the fork downward. As the fork slides down, the tool stays into the steer tube being held by the tight tolerances and the magnet.
You can guide the fork down or lightly pull it while the tool follows smoothly into the headset and frame, holding bearings, spacers, and stem in position.
The lower bearing may stay on the fork during removal. If using the Top + Bottom Kit, place that bearing onto the bottom piece, reinsert both parts into the frame, align them, then rotate 180° to lock the system together.
The magnetic tip also makes reinstallation easier. When guiding the steerer back into position, the magnet helps catch and align the tool instantly, making engagement quick and controlled.
The holding force is strong enough to keep everything composed, even allowing the bike to be turned upside down temporarily if needed during service or short-term storage.$44.90 (RRP) -
Stock Code:ABTL-STD-SOCKET-13MM
This is a 13mm socket made specifically for the bleeders on modern Fox forks. These bleeders are built just like a top cap, with minimal height of the hex drive. So it's a perfect application for our original chamferless sockets. Use these to install the fenders that mount behind the bleeders or when servicing your fork. Socket uses a 3/8" square drive
Compatibility:
Fox fork models 36,38 and 40 equipped with bleeders.
Made in Bend Oregon$52.00 (RRP)Add To Cart
