Radlabs Mountable Clip Loobtoob Pro 50ml
Description
AMC50-2 - Mountable Clip | Loobtoob Pro 50ml
Mountable Clip that holds one Loobtoob Pro 50ml with applicator when not in use-
Fits one PRO 50ml Syringe with applicator attached.
3d Printed in house - PETG Prusament
Secure fitment
Mounting Screws / Rivets not included
DOES NOT FIT BASIC OR ARDES SYRINGES
Webshops and Bike shops
You may also be interested in...
-
Stock Code:WMTL-GXP22-EXTStock Code:WMTL-BE-22MM-SETStock Code:WMTL-BE-24MM-SETStock Code:WMTL-24X37-EXTStock Code:WMTL-BE-25MM-SETStock Code:WMTL-29MM-EXTStock Code:WMTL-BE-29MM-SETStock Code:WMTL-BE-30MM-SETStock Code:WMTL-608-EXTStock Code:WMTL-609-EXTStock Code:WMTL-6000-EXTStock Code:WMTL-6001-EXTStock Code:WMTL-6002-EXTStock Code:WMTL-6003-EXTStock Code:WMTL-6804-EXTStock Code:WMTL-6805-EXTStock Code:WMTL-6806-EXTStock Code:WMTL-EX0001Stock Code:WMTL-EX0002Stock Code:WMTL-EX0003Stock Code:WMTL-BE-PUSHERStock Code:WMTL-PUSHERStock Code:WMTL-R6-EXT
6000, 6200, 6800 & 6900 (10mm) Sealed Bearing Extractor
Individual extractor for removing 6000, 6200, 6800 & 6900 sealed bearings
6000: Bearing ID: 10mm / OD: 26mm / Width: 8mm
6200: Bearing ID: 10mm / OD: 30mm / Width: 9mm
6800: Bearing ID: 10mm / OD: 19mm / Width: 5mm
6900: Bearing ID: 10mm / OD: 22mm / Width: 6mm
Insert the extractor into the bearing, tighten one side with an Allen key, and the collet expands to grip the inside of the bearing
Tap the extractor out with a punch$49.00 (RRP)$65.00 (RRP)$65.00 (RRP)$75.00 (RRP)$65.00 (RRP)$80.00 (RRP)$65.00 (RRP)$65.00 (RRP)$72.00 (RRP)$72.00 (RRP)$72.00 (RRP)$72.00 (RRP)$72.00 (RRP)$72.00 (RRP)$74.00 (RRP)$74.00 (RRP)$74.00 (RRP)$239.00 (RRP)$226.00 (RRP)$239.00 (RRP)$26.00 (RRP)$19.00 (RRP)$75.00 (RRP) -
Stock Code:PDTL6460351R
Replacement Parts for Pedro's Chain Tools.
Includes two pins made from heat-treated S2 Tool Steel, one brass pin retention nut, and one stainless steel ball bearing.
Pins and pin retention nut fit the following tools:
6460350-Pro Chain Tool (Pre-2008)
6460360-Pro Chain Tool 2.0
6460320-Apprentice Chain Tool 1.0
6460321-Apprentice Chain Tool 1.1
6460322-Shop Chain Tool
Ball bearing fits the following tools:
6460322-Shop Chain Tool
6460332-Pro Chain Tool 3.2
6460340-Tutto Chain Tool (limited 2021 units)
6460341-Tutto Chain Tool II$11.00 (RRP)Add To Cart
-
Stock Code:ABTL-SLPRS-DRVR38MM
This tool make dust wiper installation an easy sure fired task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm.
The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet.
The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time.
Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.
Made in Bend Oregon.$56.00 (RRP)Add To Cart
-
Stock Code:ABTL-WRNCH-BBQV2
With many pedal manufactures going away from 15mm wrench flats the traditional pedal wrench is becoming obsolete. To further complicate things some manufactures require both 6 and 8 mm keys within their product range. This means it's hard to know exactly what tool to grab for pedal removal or installation. Enter the Abbey Shop Pedal Wrench. With the once standard 15mm box end on one end and a custom 6 and 8 mm swivel bit on the opposite end it's the only pedal wrench you'll ever need. Perfect to keep at the fit station, on the sales floor, rental fleet counter and certainly at the tool bench.
The shop version of the tool gets an extra 2" (5 cm) of leverage over the team issue for an overall length of 14.5" Great for removing those suborn pedals. The tool receives a durable black Cerakote finish.
Made in Bend Oregon$242.00 (RRP)Add To Cart
-
Stock Code:ABTL-CHNWHP-CHNMGNTS
Now we don't pretend to understand how magnets work but they're kind of handy for keeping the chain wrapped around the cassette and keeping the chain chain stowed when not in use. So we are offering these as parts for the existing Whip-It.
$11.00 (RRP)Add To Cart
