Wheels MFG 22mm Outer Silicone Seal
Description
22mm x 41mm GXP outer seal for Wheels Mfg bottom brackets. This seal is for the non-drive side cup when using 24/22mm spindle cranksets (SRAM, Truvativ, etc).
Note: Install seal with lettering facing towards the bearing.
Fits the following bottom brackets:
- BB30 / PF30 Outboard
- BB86/92
Webshops and Bike shops
You may also be interested in...
-
Stock Code:CKBB-PBB018Stock Code:CKBB-PBB019Stock Code:CKBB-PBB003$18.97 (RRP)$18.97 (RRP)POA
-
Stock Code:WMBB-T47-BB-SHIM-BB
T47 threaded BB cups for T47 frames and 24.00mm spindle diameter cranks. Cups have internal bearings, and are typically used in BB shells with widths wider than 73mm. Machined aluminum cups thread together directly into a T47 BB shell. Bearings are easily serviced or replaced. Includes sleeve to fit between cups for added protection from dirt and grime, and also keeps your internal wires and hoses from rubbing on the crank spindle.
T47 BB cups are similar to standard BSA threaded cups in that the drive side cup is left-hand thread and the non-drive side cup is right-hand thread. Use a quality grease when installing in steel or aluminum BB shells, and an anti-seize compound compatible with titanium BB shells.
Bottom Bracket Includes:
BB Cups with bearings
2 - Silicone dust seals
2 - 0.5mm crank spindle spacers
2 - 1.0mm crank spindle spacers
Bearings: Enduro ABEC-3
Bottom Bracket/Frame Interface: T47
Bottom Bracket Shell Width (mm): 68mm - 132mm
Bottom Bracket Shell I.D.: 47x1.0mm Threaded
Crank Spindle Diameter: 24.00mm
Over Bearing Width: 91.5mm in 86.5mm wide shell*
Tool Pattern: 48.5mm x 16-notch$260.00 (RRP)Add To Cart
-
Stock Code:CKBB-AFB2Stock Code:CKBB-AFY1
** FIT KIT REQUIRED FOR USE **
ThreadFit™ T47 30x fits 68mm and 73mm shell widths with 30mm spindles.
This bottom bracket comes packed with King’s legendary, angular-contact bearings, either steel or ceramic. These are the best bearings in the industry, and actually get faster over time, as their contact surfaces wear.
You want this bottom bracket because it offers super low drag. You want this bottom bracket, because it can be opened, cleaned and repacked for years of faithful service. You want this bottom bracket, because you don’t want to think an awful lot about your bottom bracket.
- King Lifetime Warranty
- Legendary made-in-house bearings
- Threaded security with PressFit 30 shell stiffness
- A Fit Kit is required for use
- Engineered, manufactured and assembled in Portland, Oregon USA
- Uses Chris King bottom bracket cup tool for installationExpected Date:06 June 2024$330.00 (RRP)$330.00 (RRP) -
Stock Code:WMBB-ITA-30MM
The solution for running a 30mm spindle crankset in a Italian threaded frame. Machined aluminum cups thread in to a standard threaded frame and feature 6806 ABEC-3 sealed bearings outboard of the BB shell. Fully serviceable.
Notes:
- For use with 30mm diameter cranks with a spindle length of at least 106mm when used in a 70mm wide BB shell. This is the overall spindle length with all spacers and adjusters removed from the spindle. Measurement is taken from the inside face of the crank arm to the very end of the spindle.
- Will not work with standard BB30 cranksets. PLEASE MEASURE YOUR BB30 CRANK SPINDLE LENGTH!$252.00 (RRP)Add To Cart
-
Stock Code:BBBB-PF30-B3$54.08 (RRP)
Add To Cart
